Archives

  • 2026-11
  • 2026-10
  • 2026-09
  • 2026-08
  • 2026-07
  • 2026-06
  • 2026-05
  • 2026-04
  • 2026-03
  • 2026-02
  • 2026-01
  • 2025-12
  • 2025-11
  • 2025-10
  • Cy3 Rabbit Anti-Goat IgG (H+L) Antibody: Technical Guide & P

    2026-06-26

    Cy3 Rabbit Anti-Goat IgG (H+L) Antibody: Practical Use and Protocol Guidance

    What This Product Solves

    The Cy3 Rabbit Anti-Goat IgG (H+L) Antibody (SKU K1215) addresses the need for reliable and specific detection of goat-derived primary antibodies in a wide range of immunodetection assays. As a Cy3-conjugated secondary antibody, it supports sensitive fluorescence-based readouts for immunocytochemistry (ICC/IF), immunohistochemistry (frozen and paraffin, IHC-Fr and IHC-P), flow cytometry, and ELISA. The antibody is affinity-purified to minimize background and is supplied at a consistent 1 mg/mL concentration, simplifying dilution and protocol standardization. Researchers can use this reagent to achieve robust signal amplification, leveraging Cy3’s bright emission properties for quantifiable and reproducible results.

    This product is not intended for detection of non-goat primaries or for use outside fluorescence-based immunodetection. For guidance on workflow selection and validation, see the Cy3 Rabbit Anti-Goat IgG (H+L) Antibody: Workflow Guide, which outlines application boundaries and best practices. For in-depth technical usage and QC, refer to the Technical Use Guide.

    Protocol Parameters

    • Assay: Immunofluorescence (ICC/IF, IHC-Fr, IHC-P)
      Value with unit: 1:200–1:1,000 dilution (user-optimized)
      Applicability: Detection of goat primary antibodies on cells or tissue sections
      Rationale: The supplied concentration (1 mg/mL) allows dilution flexibility; starting at 1:500 is typical, but optimization for each tissue or primary antibody is recommended.
      Source type: workflow recommendation
    • Assay: Flow Cytometry
      Value with unit: 0.5–2 μg per 1 x 106 cells
      Applicability: Secondary detection of goat primary antibodies in suspension cells
      Rationale: Lower amounts help minimize background and avoid spectral overlap; titration is advised for each panel.
      Source type: workflow recommendation
    • Assay: ELISA
      Value with unit: 1:2,000–1:10,000 dilution (user-optimized)
      Applicability: Secondary antibody for ELISA detection where fluorescence readout is used
      Rationale: Higher dilutions reduce background; optimal value depends on substrate, plate type, and detection system.
      Source type: workflow recommendation
    • Assay: Storage/Handling
      Value with unit: Store at 4°C (≤2 weeks) or -20°C (≤12 months), protect from light
      Applicability: All assays/applications
      Rationale: Supplied with 23% glycerol, 1% BSA, 0.02% sodium azide for stability; light protection is essential for Cy3 fluorophore integrity.
      Source type: product information

    Workflow Setup and QC Checklist

    • Primary Antibody Source: Confirm that the primary antibody is of goat origin. This secondary will not bind other species reliably.
    • Blocking: Use appropriate blocking reagents (e.g., 1% BSA, normal serum) to reduce non-specific binding, especially in tissue sections with high Fc receptor expression.
    • Dilution Preparation: Prepare working dilutions fresh in buffer compatible with the assay (e.g., PBS with 1% BSA). Avoid buffers containing sodium azide when using peroxidase-based substrates.
    • Incubation: Protect all incubation steps from light to prevent Cy3 photobleaching. Incubate at room temperature for 30–60 minutes unless workflow dictates otherwise.
    • Wash Steps: Rinse thoroughly after each antibody incubation to minimize background. Use gentle agitation for tissue sections.
    • Aliquoting: Upon receipt, aliquot the antibody to minimize freeze-thaw cycles and maintain long-term stability.
    • Instrument Settings: For fluorescence detection, set excitation at 552 nm and emission at 565 nm (Cy3 maxima). Confirm that your instrument configuration matches these parameters.
    • QC Controls: Include a no-primary control and, if possible, an isotype control to monitor for non-specific binding and autofluorescence.

    Common Failure Modes and Fixes

    • High Background: May result from insufficient blocking, over-concentrated antibody, or inadequate washing. Optimize blocking reagents, decrease antibody concentration, or increase wash stringency.
    • Weak Signal: Could be due to low primary antibody concentration, expired or photobleached secondary, or incorrect filter settings. Check the age and storage of the antibody, confirm instrument settings, and optimize primary/secondary titration.
    • Cross-Reactivity: Non-goat primaries may yield false positives. Ensure the primary antibody is goat-derived. If using in multiplex panels, validate specificity for each component.
    • Photobleaching: Cy3 is sensitive to prolonged light exposure. Always protect slides and samples from light during and after staining. Use antifade mounting media for microscopy.
    • Aggregates/Precipitate: May occur if the antibody is repeatedly freeze-thawed or stored improperly. Aliquot upon arrival and avoid repeated temperature cycling.

    Scope and Limitations

    This Cy3-conjugated secondary antibody is optimized for detection of goat IgG (H+L) in immunofluorescence, immunohistochemistry, flow cytometry, and ELISA where a fluorescent readout is appropriate. It should not be used with non-goat primary antibodies, non-immunoglobulin targets, or in non-fluorescent detection formats (e.g., chromogenic IHC, Western blot without fluorescence detection). There is no evidence for use in workflows such as live-cell imaging or multiplexed imaging without prior validation. For detailed guidance on application boundaries, see the Workflow Guide.

    The antibody's performance is dependent on adherence to recommended storage, handling, and protocol setup. Its specificity is verified through affinity purification, but off-target binding or background may still occur if protocols are not carefully optimized. APExBIO provides batch-specific quality control, but end-user validation in their own system is essential.

    Conclusion

    The Cy3 Rabbit Anti-Goat IgG (H+L) Antibody offers a robust solution for sensitive detection of goat IgG primaries in fluorescence-based assays. Its affinity-purification and Cy3 conjugation ensure reliable signal amplification for immunocytochemistry, immunohistochemistry, flow cytometry, and ELISA. Following best practices for dilution, storage, and workflow setup is critical to achieving reproducible, high-quality results. For further protocol and troubleshooting information, researchers are encouraged to review the technical and workflow guides linked above. Use within validated formats as specified by APExBIO and product documentation.